I Want To Create For
Crafting for Occasions
0 items
Shopping Cart

Candy Cane Pendant

Make this holiday pendant special with personalization.
not yet rated   AT A GLANCE
Skill Level: Beginner


FolkArt ® Metallics - Pearl White, 2 oz.
Item #659
Premium, all-purpose shimmering metallic acrylic paint for decorative crafts and home décor. Superior coverage. Exceptional brushability. Use on all porous surfaces. All colors are certified AP non-toxic, water-based, and acid neutral.


FolkArt ® Acrylic Colors - Wicker White, 2 oz.
Item #901
Premium, all-purpose acrylic paint for decorative crafts and home decor. Superior coverage. Exceptional brushability. Use on all porous surfaces. All colors are certified AP non-toxic, water-based, and acid neutral.


Mod Podge ® Gloss, 8 oz.
Item #CS11201
Mod Podge ® is quick-drying for multiple coat build up and dries clear. Can be sanded to a smooth finish. Cleans up easily while wet with soap and water. Certified AP non-toxic; waterbase. Mod Podge ® is an all in one decoupage glue, sealer and finish


Other Supplies
1-1/2” round silver pendant blank
Crinkled silver scrapbook paper
Metal stickers
Peppermint and holly stickers
Silver metal adhesive-backed dots
Small bristled paint brush
Xacto knife
1/8” green satin ribbon
1/8” white satin ribbon
Metallic silver cord
2 large hole silver beads
1 set of silver hook and eye cord ends
8” silver wire - 24 gauge
Needle nose pliers
Wire cutters
Bead glue


  1.  Trace the pendant on the back of the textured silver paper.
  2. Paint the circle with Wicker White. Allow to dry. (TIP: Paint using a small circular motion rather than a straight brushstroke. This will distribute the paint more evenly on the textured paper and will dry more quickly.)
  3. Paint over the Wicker White with the Metallic Pearl White. Allow to dry.
  4. Using scissors, cut out the circle and attach to the pendant using the Mod Podge. Trim any excess paper from around the pendant with the Xacto Knife. Allow to dry.
  5. Remove any excess Mod Podge from the back of the pendant.
  6. Adhere stickers to the pendant, using the photo as a diagram for placement.
  7. Apply 2 coats of Mod Podge over stickers  and allow to dry between coats. 
  8. Adhere metal initial and metal dots to the pendant using the photo as a diagram for placement.
  9. Apply a final coat of Mod Podge over the entire surface and allow to dry completely. 
  10. Thread pendant onto all three ribbons and hold up with both ends of the ribbons even to find the center of the ribbons. 
  11. Tie one knot on both sides of pendant to keep the pendant from shifting during wear. Knots should be approximately 1” apart with the pendant between them.
  12. Thread one silver bead onto ribbons on both sides of the pendant. Push bead on each side down to sit on knot. 
  13. Tie 2nd knot on the other side of each bead to keep the beads in place.
  14. Continuing tying single knots in all three ribbons approximately every 2” to the end of the ribbons.
  15. Cut silver wire into to 4” pieces. Wrap wire once around the ribbon ends at the desired approximate length. Twist wire ends together using the needle nose pliers to secure. Cut excess wire and ribbon at the last ribbon knot. 
  16. Secure ribbon ends in eye clasps using the bead glue. Attach hook clasp to one eye clasp and squeeze one side of the hook clasp closed with the needle nose pliers. Allow to dry.
Disclaimer: The information found in each project is presented in good faith, but no warranty is given, nor results guaranteed, nor is freedom from any patent to be inferred. Since we have no control over physical conditions surrounding the application of information herein contained, Plaid Enterprises, Inc. disclaims any liability for untoward results.

Important: Please be sure to thoroughly read the instructions for all products, paying particular attention to all cautions and warnings shown to ensure the proper and safe use of the product.

Copyright: All Rights Reserved. No part of this Project may be reproduced in any form without permission in writing, except for your personal use, except by reviewer, who may in reviewing this project, quote brief passages in a magazine or newspaper.