 |
|
|
|
|
Artistrywear Snowman Pendant and Earrings
Marianne Ajamy
|
This project is not available online. Please check with your retailer for supplies. |
 |
6 Black Seed Beads |
|
3 Orange Bugle Beads |
|
10 Silver Spacers |
|
7 Silver Crimp Tubes |
|
2 Fish hook silver earrings |
|
2 silver designer head pins 3” |
|
Copper tin wire 24 gauge |
|
Roundnose Pliers/Clippers |
|
Crimp Tool |
|
Jewel Glue |
|
Tweezers |
|
Pin Back |
|
Earring stopper |
- To make the Pendant/Pin use 4 Silver Discs, 2 Black Dot Cylinders, 3 Silver Spacers, 2 Black Glass beads, 1 Orange Bugle Bead. 24 Gauge Wire Cut 3- 6” lengths of wire.
- For the Body: Put crimp tube on end of 1 wire, put 1 silver spacer on, then wrap wire around silver spacer, thread into crimp tube and crimp. Put aside construct arms.
- Arms: With each of 2 remaining 6” wire. Slide silver spacer on end, coil about 1” of end wire, wrap around Roundnose pliers about 3 times. Flatten coil make sure end is inside coil. Thread 1 Black Dot Cylinder bead on wire. Do the same for the next arm.
- Construct: Thread 2 Silver Discs onto 1st. Take each arm and wrap wire around body wire. Cut ends to fit up inside head. Slide 3rd Silver Disc onto top put arm ends inside head disc. Slide silver spacer on body wire on top of head with round nose pliers wrap wire around spacer and twist underneath to secure. Or make a wrapped loop to attach to necklace with o rings.(optional). Wrap arms around base to put into pleasant position-this closes up space between head and remainder of body.
- With Jewel Glue, glue 2 black seed beads and 1 orange bugle bead onto top Silver Disc to make snowman’s face. Let dry. Glue Pin back onto back slide earring stopper into place, when using as a pendant, will keep pin from sliding on necklace.
- Earrings: Slide silver spacer onto 1-3” head pin, slide Silver Disc make a wrap loop on end. Glue black glass beads for eyes and orange bugle beads for nose. Make other earring the same way. When dry attach to fish hook earrings.
- Plaid Paper Couture Silver Slide Clasp Necklace Kit. Use all wire in kit cut in thirds, cut 3 wires approximately 22” long. Slide 2 silver crimp tubes to center of wire at abt 11” and crimp. Slide another silver crimp bead onto 1 side, measure 2” from center, crimp into place. Slide silver spacer, Silver Cube Bead, silver spacer and silver crimp tube, crimp into place. Do the same for other side. Construct necklace clasp following package directions.
- Pendant is pinned on neckace in center use the earring stopper to hold pin in place. Or wear adorable snowman as a pin. Enjoy.
|
|
Disclaimer: The information found in each project is presented in good faith, but no warranty is given, nor results guaranteed, nor is freedom from any patent to be inferred. Since we have no control over physical conditions surrounding the application of information herein contained, Plaid Enterprises, Inc. disclaims any liability for untoward results.
Important: Please be sure to thoroughly read the instructions for all products, paying particular attention to all cautions and warnings shown to ensure the proper and safe use of the product.
Copyright: All Rights Reserved. No part of this Project may be reproduced in any form without permission in writing, except for your personal use, except by reviewer, who may in reviewing this project, quote brief passages in a magazine or newspaper.
|
|
